I’ve been playing around with the idea of morphing a t-shirt and skirt into one piece for a while now. I finally tried it. This is the result:
I’ve hung on to this skirt for several years. I love the print but the skirt just didn’t fit me quite right after Jack was born. Bummer. I saved it hoping my body would return to its former shape. No luck.
This turned out to be a pretty easy project. If you’d like to know how it was done, read on!
The T–Skirt Tutorial
Here’s what you’ll need:
You’ll also need thread to match your t-shirt and your skirt. (You might need one more t-shirt to get the job done. Or not. Keep reading, and then decide.)
And that’s all you need.
Put on the t-shirt; then put the skirt on over it, right where you want it to rest around your chest. Safety pin the front; ask a family member or friend to help you safety pin the back. (If you’ve never met your neighbors, now’s a great time to break the ice.)
I am digging the photo above. I never look busty.
Note: I inherited a “gross” of safety pins from my mom years ago. Sometimes I just want to use them so I can justify keeping them. How much is a gross, anyway? A LOT. Anyway, in the step above, regular straight pins would have worked just fine.
At this point you can either 1) turn the piece inside out and cut away the length of the t-shirt to about 1/2" away from the seam you just sewed, or 2) leave it as is and wear your t-skirt with the full shirt underneath. I had planned to cut away the shirt length, but when I tried the piece on the spandex held in my two-baby stretch a bit. So I kept the entire t-shirt intact.
If you cut away the t-shirt length, congratulations—you have fabric to embellish your t-skirt. If you decide to leave the shirt intact, you’ll need to round up another t-shirt for embellishment. I chose this one:
There are lots of ways to embellish with the t-shirt fabric or with any skirt fabric you’d like to cut from the length. This was my initial sketch of the project:
I decided that although I like this sketched design in theory, I wasn’t sure I would end up wearing it. So I changed my mind. Be sure to change yours too, if you like. But here’s exactly what I ended up doing.
Just below the skirt’s elastic waist, I sewed a 1" band of t-shirt fabric around the chest. I cut two 1"-wide strips from the width of the t-shirt—one about 1/2" longer than the skirt front, and one about 1/2" longer than the skirt back. No need to measure; just cut strips from the t-shirt, lay them across the front/back widths of the skirt, and cut the strips at least 1/2" longer than that.
Pin the back strip to the back of the skirt. Using a 1/8" seam, sew along the top of the strip. Repeat along the bottom of the strip. The strip should reach past the side seams of your skirt by about 1/4". Pin and sew the front strip to the front of the skirt in the same manner, overlapping and sewing over the back strip at beginning and end.
When I tried on the piece again I decided the skirt was a bit too long for me, so I cut away 1 1/2" in length from the bottom. To do that, I measured 1 1/2" from the bottom hem all around the skirt, making dots with a washable marker every two inches or so; then I cut along the dots with scissors. I tried it on and liked the length better.
I added a thick, doubled black border to the bottom of my t-skirt. I cut two 4"-wide strips from the width of the t-shirt—one 1/2" longer than the skirt front, and one 1/2" longer than the skirt back. Again, no need to measure; just cut strips from the t-shirt, lay them across the front/back widths of the skirt, and cut the strips at least 1/2" longer than that. Press the strips in half lengthwise, wrong sides together, and then unfold.
With right sides together, align and pin one long edge of the border along the back of the skirt; sew using a 1/4" seam. Repeat to attach the front border to the front of the skirt, overlapping and sewing over the back border at beginning and end. Press the seam toward the bottom of the skirt.
Pin the short sides of the two overlapping borders together, making sure the seam you pin is perpendicular to the border seam you just sewed. Use a tight zigzag stitch to connect the short edges of the borders. Clip any overlapping fabric on the wrong side to 1/4", if needed.
Fold the border to the wrong side of the skirt, using the fold you pressed in earlier as a guide; pin. Change the thread on your machine to match the skirt. Sew the border layer to the bottom of the skirt using a 1/8" seam.
Now, I know I’m not model material. (Reason one: I’m 39. Reason two: I wear glasses. There are more reasons, but I’ll stop at the main two.) At the same time, I love to sew things to wear. When I see what others have sewn to wear, I really like to see the project on a body; it helps me envision what it might look like on me if I make it. I think others who sew might like that too. So, a bit uncomfortably, I asked Bretty to take some pictures of me in my t-skirt.
Brett: “I dunno. Just do something else. Look in the pot. Imagine that you love the pot.”
I look down into the pot.
Me: “Oooh, I love the pot!”
And that’s the end of my t-skirt story.
There are many variations for playing around with this basic idea—as many as there are skirts and t-shirts! If you make one, I would love to see it. You can upload your photos here.
Hope you enjoyed your visit here. For more refashions you can check out my book ReSew. Thanks for stopping by!